2N 2N 2N Units. Collector – Emitter Voltage. VCEO. . verify that the information in this data sheet is current before using this product. Visit for additional data sheets and product information. Forward Current Transfer Ratio. IC = 10 Adc, VCE = 3 Vdc. 2N 2N NPN POWER SILICON TRANSISTOR. Qualified per MIL-PRF/ T4- LDS Rev. 1 (). Page 1 of 5. DEVICES. LEVELS. 2N 2N

Author: Nagore Natilar
Country: Comoros
Language: English (Spanish)
Genre: Love
Published (Last): 26 September 2008
Pages: 297
PDF File Size: 4.40 Mb
ePub File Size: 12.53 Mb
ISBN: 489-5-69868-196-6
Downloads: 49073
Price: Free* [*Free Regsitration Required]
Uploader: Yozshulmaran

Datahseet the output-mode control connected to the reference line, the pulse-steering flip-flop directs the modulated pulses to each of the two output transistors alternately for push-pull operation. This makes it less cost effective at the lower power levels. Here devices that would normally be used in switchers from 10 to watts are listed next to circuits in which they would generally be used.

Primary Inductance Is 4.

The regulating circuit that is finally accepted will be a compromise between such factors as performance, cost, size and complexity. This handbook describes Motorola’s voltage regulator products and provides information on applying these datashdet.

【FMLLF】Electronic Components In Stock Suppliers in 【Price】【цена】【Datasheet PDF】USA

This output can be used to clock an edge triggered flop- datssheet whose output inhibits or shuts down the power supply when the OVP trips. Therefore, in order to arrive at a suitable heatsink design, a trial size is selected, its dSA evaluated, and the original size reduced or enlarged as necessary. Because full line rather than half is applied to the primary winding, the power output can almost double datashete of the half bridge with the same switching transistors.

This is done by using an external pass element and a zener level shifter as shown in Figure B. When choosing ICs that are not exact replacements, 2n624 operating needs and performance aspects should be considered. The circuit operates in the following manner; when Yqc rises above the trip point set by R1 and R2, the internal current source begins charging the capacitor, Cp, connected to pins 3 and 4.


This is only a small example of the conventions used in IC part numbers. Organization is first by regulator datasheeg and then by variants, such as current boost. The colored areas have the following significance.

【FM101LLF】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA

This feature allows the OVP circuit to operate in noisy environments without nuisance tripping. If no other common supplies or system components operate off catasheet input datashete to the regulator, the circuits of Figures 2- 1 c and 2- 1 d may be used to regulate datasheeet voltages with a negative regulator and vice versa. Besides the transformer, only three other components are employed: These are instantaneous values.

For illustrative purposes, pass elements for only positive regulator types will be discussed. Value shown is The fixed drive circuits of 1 1- 4A and 1 1 -4B tend to emphasize economy, while the Baker clamp and proportional drive circuits of 1 C, 1 D and 1 E emphasize performance over cost. Resistor R1 sets the vaiue of iref: Package Outline Dimensions Section Finally, high voltage 1. Very often a mV switching spike at the output may be attenuated considerably at the load datasgeet due to the series inductance of the connecting cables and the additional filter capacitors found in many logic circuits.

Choose a replacement IC that operates at or above the circuit clock speed. In addition, it can be seen for Equation 4. Resistor R4 is used to guarantee that the power supply will have a minimum output load current datassheet 1.

Here, the dc feedback signal is compared to a fixed frequency sawtooth or triangular wave- form.

2N 데이터시트(PDF) – Central Semiconductor Corp

Although foldback current limiting allows use of smaller pass element transistors for a given regulator output current than does constant current limiting, it does have a few disadvantages. If greater current capability is required, or if the IC regulator does not possess sufficient safe-operating-area SOAthe addition of an external series pass element is necessary.


Another very useful reference tool for working with ICs is IC Master, a master selection guide that organizes ICs by type, function and certain key parameters. Figure C shows this configuration. Thus, we can test devices near their maximum junction tem- peratures, analyze the failures to assure that they dafasheet the types that are accelerated by temperature and then by applying known acceleration factors, estimate fatasheet failure rates for lower junction temperatures.

They provide the designer with a cost incentive over the discrete, or a simpler control circuit, or both. Even if a single transistor with sufficient capability is available, it is possible that paralleling two smaller transistors is more economical. Buy American, Buy Direct.

For the above conditions, the heatsink thermal resistance can be approxi- mated by: Furthermore, such information does not convey to the purchaser of the semiconductor devices described any license under the patent rights of Motorola Inc. Spec 55A, Voltage Rating: The output is bypassed using a small 0. R2 is therefore chosen to consist of a 62K resistor and a 2K trimpot. To activate the shutdown feature, a 1mA minimum, 10mA maximum current is applied to pin 2 of these regulators.

An Aiternate Method of Sensing Line Fauit and Overvoitage Conditions for Linear Power Suppiies and medium sized computer systems which must store part or all of the data currently being processed before the power failure. However, at present, most designers find it less costly and more effective to add a high frequency noise filter rather than use a relatively expensive capacitor with low equivalent series inductance ESL.

The transistor type chosen for Q1 datashfet have the following characteristics see Section 4: E cores expose the windings to air so that heat is not trapped inside.