Seamless Fittings per ASTM/ASME A / SA in a variety of stainless grades: /L; H; ; /L; ; /H; /H; Duplex ASTM A Standard Grades are designated with a prefix, WP or CR, based on the applicable ASME or MSS dimensional and rating standards, respectively. ASTM A / ASME SA ASTM A / ASME SA ASTM A / ASME SA ASTM A TUBE ASTM A / ASME SA ASTM A / ASME SA
|Published (Last):||11 July 2012|
|PDF File Size:||3.91 Mb|
|ePub File Size:||6.31 Mb|
|Price:||Free* [*Free Regsitration Required]|
Link to Active This link will always route to the current Active version of the standard. Class designations are also utilized to indicate the nondestructive test method and extent of nondestructive examination NDE. Fabricated large size stainless steel fittings, duplex stainless steel buttweld fittings, stainless steel elbow, stainless steel tee, stainless steel reducers, stainless steel cap, stainless steel stub ends.
These comparisons are approximate only. Elbows are produced according to the following standards: There are no classes for the CR grades. DINsteel grades St. The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products.
Steel reducers are produced according to the following standard: Historical Version s – view previous versions of standard.
All sales are governed by our terms and conditions, which aa403 available on request. A combination of values from the two systems may result in nonconformance with the specification.
A stainless steel welded and seamless fittings
Wrought stainless steel butt-welding fittings. Specific requirements are covered elsewhere. We reserve the right to asmw or improve the designs or specifications of our products at any time without notice. Tension test shall be done on the fitting material to determine the tensile properties such as yield strength and tensile strength. All fittings shall undergo heat-treatment.
ISO Approved Manufacturer & Exporter of ASTM A403 WP 304L Stainless Steel Buttweld Pipe Fittings.
This abstract is a brief summary of the referenced standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
They are produced according to the following standards: Chemical and product analyses shall be performed and shall conform to the required chemical composition in carbon, manganese, phosphorus, sulfur, silicon, chromium, molybdenum, and titanium. The contents of this website are presented for information purposes only, and while effort has been made to ensure their accuracy, they are not to be contrived as warranties or guarantees, expressed or implied, regarding the products or services described herein or their use or applicability.
Table 1 is a general summary of the fitting classes s403 to all WP grades of stainless steel covered by this specification. Stainless Steel forging or shaping operations shall be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, fusion welding, machining, or by a combination of two or more of these operations. Class designations are also used to indicate the nondestructive test method and extent of nondestructive examination NDE.
Chemical and product analyses shall be performed and shall conform to the required chemical composition in carbon, awme, phosphorus, sulfur, silicon, chromium, molybdenum, and titanium.
DINsteel grades: It is informational only and not an official part of the standard; the full text of the standard itself must be referred aeme for its use and application. Referenced Documents purchase separately The documents listed below w403 referenced within the subject standard but are not provided as part of the standard. Combining values from the two systems may result in non-conformance with the standard.
Stainless Steel Fittings Manufacturers in India. Stainless Steel Pipe Fittings Manufacturers. It is easily accessible through NH No.
Forged steel fittings socket-welding and threaded. S ENsteel gades: There are no classes for the Assme grades. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Within the text, the SI units are shown in brackets. Now FitTech has emerged with high volume of quality production at reduced time with competitive price focusing totally on customer satisfaction with high class quality with committed early delivery at competitive price. Forging or shaping operations shall be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, fusion welding, machining, or by a combination of two or more of these operations.
Specific requirements are covered under another specification.