ASTM A386 PDF

ASTM-A › Zinc Coating (Hot-Dip), Assembled Steel Products. ASTM-A – EDITION – SUPERSEDED — See the following: ASTM-. in Specifications A and A This ASTM Standards A47/ A47M 1 This specification is under the jurisdiction of ASTM Committee A05 on. ASTM AAM Standard Specification for Zinc – Standard A and A shall be done using the metric equivalent of the test.

Author: Moogurg Akigor
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Finance
Published (Last): 24 March 2011
Pages: 457
PDF File Size: 14.76 Mb
ePub File Size: 14.86 Mb
ISBN: 943-7-12017-139-8
Downloads: 64244
Price: Free* [*Free Regsitration Required]
Uploader: Vosho

Except for local excess coating thickness which would interfere with the use of the product, or make it dangerous to handle edge tears or spikesrejection for nonuniform coating shall be made only for plainly visible excess coating not related to design factors such satm holes, joints, or special drainage problems see Note 6.

Gas Nitriding of Titanium Alloys: For thickness testing purposes, articles whose surface area is greater than in.

The thickness of coating thus obtained is the test a3386 coating thickness, or in the case of a specimen removed from a test article, is the specimen average coating asym. Likewise, do not use removal of small particles of the coating by paring or whittling to determine failure. NOTE 6—The requirements for the?

If a zinc alloy is used as the primary feed to the galvanizing bath, then the base material used to make that alloy shall conform to Speci?

ASTM Standard List: Coated Steels

Plain holes of 1? Introduction to Total Materia 7 th February Surfaces that remain uncoated after galvanizing shall be renovated in accordance with the methods in Practice A unless directed by the purchaser to leave the uncoated areas untreated for subsequent renovation by the purchaser.

Where products consisting of various material thicknesses or categories are galvanized, the coating thickness grades for each thickness range and material category of material shall be as shown in Table 1. In the case of any such local section containing more than one material category or steel thickness range as delineated in Table 1, that section will contain more than one specimen see Fig.

Practices AAand A provide guidance for steel fabrication for optimum hot dip galvanizing and shall be complied with in both design and fabrication. In addition, the purchaser should anticipate the need for test batches or extra preparation steps, or both, such as blasting before galvanizing or other methods, to attempt to reach the higher requirements with consistency. A specimen must be evaluated for each steel category and material thickness within the requirements for each specimen of asgm test article.

  AGMA 923-B05 PDF

ASTM B standard spe Each system shall be used independently of the other without combining values in any way. In the case of an article containing more than one material category or steel thickness range as delineated in Table 1, that article will contain more than one specimen, as appropriate see Fig.

This new sample shall be measured using magnetic thickness gages which have been calibrated for accuracy against reference material thickness standards. Xstm a phrase to search for: This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Finding ASTM materials astn standards from specific designation systems in the Total Materia database With Total Materia finding information about a metal standard specification, its current status and the materials it defines is one click away. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

For more information on the ASTM designation system see our related article: In such case, the now-smaller lot shall be treated as a new lot for purposes of inspection and acceptance.

ASTM-A | Zinc Coating (Hot-Dip), Assembled Steel Products | Document Center, Inc.

The accuracy of both methods will be in? A superscript epsilon e indicates an editorial change since the last revision or reapproval. They do not address the matter of measured coating thickness variations that can be encountered because of different steels or different thicknesses of ashm given steel being used in an assembly.

While most coating thicknesses will be in excess of those values, some materials in each category may be less reactive for example, because of chemistry or surface condition a3386 other materials of the steel category spectrum. ASTM specifications represent a consensus among producers, specifiers, fabricators, and users of steel mill products.

The galvanizing of separate reinforcing steel bars shall be in accordance with Speci? The zinc coating on threaded components of articles galvanized under this speci? Dynamic Strain Aging of Steels: The adhesion shall be considered inadequate if the coating?

NOTE 1—Each specimen comprises nominally one third of the total surface area of the article. Introduction to Total Materia Integrator 7 th March Practice A provides guidance on steel selection and discusses the effects of various elements in steel compositions for example, siliconthat in?

  LIBRO ENRIQUILLO EN PDF

This shall be achieved by an in-plant inspection program designed to maintain the coating thickness,? Click here to see more. NOTE 7—Items which are prepared for galvanizing by abrasive cleaning will generally develop a thicker coating with a moderately rougher surface.

ASTM Standard List: Coated Steels :: Total Materia Article

Therefore, some articles may have a coating grade at or close to the minimum requirement shown in Table 1. The galvanizer shall afford the inspector all reasonable facilities to satisfy him that the zinc coating is being furnished in accordance with this speci?

Terminology A contains other terms and de? If Test Method B is used, the level of sampling shall be agreed upon between the galvanizer and the purchaser at the time the coating order is placed. Total Materia remains the only tool which will be used for this purpose.

Consultation between the designer, fabricator, and galvanizer at appropriate stages in the design and fabrication process will reduce future problems. In the case of orders in inch-pound units, the measured value shall be converted to coating grade units by the use of Table 2.

In the case of orders in SI units, all testing and inspection 1 This speci? Metallic coated carbon steel wire coated at size for mechanical springs Composite ribbed steel pipe, pre-coated and a3886 lined sewer pipe application Flexible poly vinyl chloride PVC gaskets used in connection of water closets to sanitary drainage system For more information on the ASTM designation system see our related article: Do not use testing carried out at edges or corners points of lowest coating adhesion to determine adhesion of the coating.

Astmm 5—Inaccessible surface areas are those which cannot be reached for appropriate surface preparation and application of repair materials as described in Practice A Closed Rib Steel Pipe with Xstm of 36 in. To get started, click on the standard list button in the menu bar.