ASTM D/DM() includes six different test methods, depending on the specific conditions of the test and type, to be used for. Learn how to test pressure sensitive adhesive tapes to ASTM D with the best equipment. This standard is issued under the fixed designation D/DM; the number 1 This test method is under the jurisdiction of ASTM Committee D10 on.
|Published (Last):||16 May 2008|
|PDF File Size:||10.11 Mb|
|ePub File Size:||15.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
Next, clamp the substrate panel into the moveable jaw of testing machine and free end of tape into other jaw. A strip of tape is applied to a standard test panel that with controlled pressure from a TestResources Sample Roller. Place the panel into the peel test machine grips and peel back 22 mm of aetm bottom half of the tape sample so that the specimen is doubled over itself at degrees. Fold over 12 mm at one end, adhesive to adhesive to form a tab.
ASTM D Peel Adhesion Pressure Sensitive Adhesive Tapes
Other sample widths available upon request Effective and simple to use Blade replacement takes mere seconds. MEGA Auto Tensile Tester MEGA Auto Tensile Tester is professionally designed for the determination of tensile strength, peel strength, tear strength, heat seal strength and adhesiveness of plastic films, composite films, flexible packaging materials, adhesives, adhesive tapes, pressure sensitive tapes, medical patches, awtm films, release paper, rubber and paper, etc.
These simple and effective grips have 30mm wide jaws, perfect for the majority of sample sizes. When testing liner side adhesion, the face side adhesive is adhered to a r3330 polyester film. Adhere the tape specimen onto the test panel using a handheld roller. The force will be different at other peel rates. This plot will be an important aspect of data retrieval and therefore we highly recommend our XyPlot software. These characteristics will result in a high variability for the test response which is not a true indication of the real nature of the adhesive bond.
GK Mechanical Vice Grip.
ASTM D / DM – 04() Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape
ASTM D Method F measures the adherence of single-coated tapes to a standard steel panel or your chosen substrate when peeled c3330 a 90 degree angle. The peel adhesion of the liner is measured using a degree peel test.
Referenced Documents purchase separately The documents listed below d33330 referenced within the subject standard but are not provided as part of the standard. The values stated in each system may not be exact equivalents, therefore, each system must be used independently without combining values sstm any way. ASTM D Test Method D provides a means of assessing the uniformity of the adhesion of a given type of pressure-sensitive adhesive tape.
XLW EC Auto Tensile Tester XLW EC Auto Tensile Tester can be used to measure tensile, peeling, deformation, d33330, heat sealing, adhesive, puncture force, opening force and low speed unwrapping force as well as other performance of plastic films, composite materials, soft package materials, plastic flexible tube, adhesives, adhesive tape, label stickers, medical plasters, release paper, adtm films, combined caps, aluminium foil, diaphragm, back sheets, non-woven fabrics, rubber, paper, etc.
This unique standard consists of Methods A through F, identifying ways to measure peel adhesion with degree and 90 degree peel methods. Forces up to 10 kN 2, lbf Low force tabletop systems Modular series of five frame options with adjustable test space Affordable testing option for tension, compression, bend, peel and much more.
The P consists of a vertical load frame, an electromechanical actuator, load cell, a tocuhpad test controller, XY test software and peel grips.
A key issue that many people encounter when testing degree peel tests to ASTM D, is that both sides of the adhesive specimen can accidentally rub together during testing. If you would rather see the data in real-time and study the peel interface at the same time, we would provide you with our XyLive Software. D Terminology of Packaging and Distribution Environments. In a face-side application, the tape is adhered to a standard steel panel or your chosen substrate in the same manner as the previous methods mention with pressure sensitive tape.
If this occurs, the friction of that touching will cause errors in the peel force data. The data obtained provide a means of assessing the uniformity of the adhesion of a given type of pressure-sensitive adhesive tape.
For Method B, measure out several strips of the tape according to the standard.
XLW Auto Tensile Tester XLW Auto Tensile Tester is applicable to the determination of physical mechanical properties of plastic films, laminated materials, flexible packaging materials, plastic flexible tube, adhesives, adhesive tapes, pressure sensitive tapes, adhesive bandage plasterrelease paper, protective films, flip off cap, foil, diaphragm, back sheet, non-woven, rubber, and paper fiber, etc.
Fold a tab of the tape and double back at an angle of degrees. The area under stress varies with backing stiffness and adhesive rheology firmness. The 25mm wide jaws are better for aligning smaller sample sizes. The plate is placed horizontally into the test machine and the free end of the tape is grasped in the machine grips. The G are small and precise, perfect for very small load cells testing at low loads.
The tape is then pulled from the plate at a degree angle at a specified rate, and peel adhesion is measured. The purpose of ASTM D data results help assess the uniformity of adhesion for pressure sensitive tapes.
Now apply a strip of the tape to a rigid panel, such as the standard stainless steel panel. Testing is then conducted for degree peel adhesion. XLW Auto Tensile Tester is applicable to the determination of physical mechanical properties of plastic films, laminated materials, flexible packaging materials, plastic flexible tube, adhesives, adhesive tapes, pressure sensitive tapes, adhesive bandage plasterrelease paper, protective films, flip off cap, foil, diaphragm, back sheet, non-woven, rubber, and paper fiber, etc.
For this test we recommend that care be taken in aligning the grips to prevent the backside of the tape specimen from rubbing. Request a Quote Today Need help or have a question? This is because the measured peel force is not normalized for a fixed area of stress.
Secure the loose end of the tape with the tab into the upper grip.
This method is the same procedure as Method A, but measured for the thin polyester film applied to double-coated tape. Contact Now Ask for more details or tell us your test requirements.
G Series Pneumatic Grip. Rated to N 50 lbf Maximum specimen thickness of 8 mm 0. Rated to 1 kN lbf Maximum specimen thicknesses from 10 mm to 50 mm 0. In a liner-side application, the transfer tape is applied to a strip of 0.
If the adherent is set on an angle, that will cause an error. Although we can provide you with guidance, we recommend you purchase and closely follow the ASTM International testing standard. Substitution of representative samples of materials in question for the standard steel panel would suffice to do this.