A major revision to ASTM F has been completed and the new specification will appear in the ” ASTM Book of Specifications Volume Plastic. ASTM F (D) Conduit · Innerduct Warranty · Innerduct Material Specification · F (D & D) Complete Part Number Chart · Enduct True. F (D) Data Sheet · ASTM F Conduit All Types · Innerduct Material Specification · Part Number Chart · Innerduct Warranty · ASTM F (D).
|Published (Last):||18 May 2012|
|PDF File Size:||5.47 Mb|
|ePub File Size:||12.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
The internal or external surface may contain a coextruded layer provided the finished conduit meets the product requirements of this specification. Search book title Enter keywords for book title search.
Enduct F O.D Controlled Conduit
Since specifications vary from customer to customer, we perform in-house lab tests on resins and finished products which include, but are not limited to the following: You currently cannot view this content. This standard does not purport to address all of the safety concerns, if any, associated with its use.
Polyethylene Plastic Pipe asttm Fittings Materials. The internal or external surface may contain a coextruded layer provided the finished conduit meets the specified product requirements.
There is no additional charge for Striped Duct. Application High Density Polyethelene Duct has been tested and proven under the most severe conditions. Polyethylene Plastics Molding and Extrusion Materials.
Couplings Couplings should be available to quickly connect the duct and should be air and watertight i. Content only available by subscription.
The internal or external surface may contain a coextruded layer provided the finished conduit meets the product requirements of this specification. It shall be possible to bend the duct to a minimum supported radius of 10 diameters.
The duct shall be capable of being coiled reeled in continuous lengths, transported, stored outdoors and subsequently uncoiled for installation – without affecting its properties or performance. There were no books found f21600 the applied search filters.
ASTM F2160 – 16
Color The duct for exposed areas black shall have a minimum of carbon black. Pull Rope and Lubricant The duct should be equipped qstm a factory installed rope or tape and pre-lubed to aid in the installation of cable. Historical Version s – view previous versions of standard. Enter your account email address to request a password reset: Request the technical instruction guide for C.
The product shall be subject to elongation, impact, and ovality tests. The right to access the electronic files of ASTM Standards is for purposes of viewing for individual use only. This abstract is a brief summary of the referenced standard.
Flow Rates of Thermoplastics by Extrusion Plastometer. Environmental Stress-Cracking of Ethylene Plastics. Packaging The duct should be provided on lightweight metal reels in maximum lengths possible f2610 no joints or splices. The rope can be provided with varying strengths as needed for a particular installation. This shows different design parameters for polyethylene pipe i.
No further reproductions authorized. Ovality out-of-roundness and curvature are inherent characteristics of coiled, continuous length HDPE conduit. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health t2160 and determine the astj of regulatory requirements prior to use.
Remember me for one month. Other special markings can be agreed upon between the buyer and seller. In addition the electronic files may not be downloaded or distributed elsewhere over computer networks or otherwise. Tests on Resins and Finished Duct Since specifications vary from customer to customer, we perform in-house lab tests on resins r2160 finished products which include, but are not limited to the following: Installation The duct shall be capable of being direct buried by plowing or trenching with no special consideration to using selective backfill.
This specification covers material, dimensional, workmanship and performance requirements for polyethylene conduit, duct and innerduct manufactured for use in a nonpressure application with communication, CATV, or power wire and cables. The duct shall also be capable of being encased in asm.