Buy DIN EN E: CHARPY IMPACT TEST ON METALLIC MATERIALS – TEST METHOD from SAI Global. Purchase your copy of BS EN as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. Find the most up-to-date version of DIN EN at Engineering
|Published (Last):||10 March 2004|
|PDF File Size:||6.55 Mb|
|ePub File Size:||9.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
Methode d’essai Title in German Metallische Werkstoffe. EU, Impact testing using V-notch, beam type test piece.
It represents the first part of the general standard: The ne piece shall be broken within 5 seconds of the time of removal from ein medium.
In the centre of the length, there shall be a notch. Part 4BS Take the smart route to manage medical device compliance. NOTE It is emphasized that only results on test pieces of identical dimensions should be compared.
The test report shall state that the test piece was 1004-51 broken by x J. This absorbed energy is a measure of the impact strength of the material. EUCharpy impact test for steel. Find Similar Items This product falls into the following categories. The values of the principal characteristics of the testing machine are specified in Table 3.
BS EN 10045-1:1990
You may find similar items within these categories by selecting from the choices below:. This European Standard replaces the Euronorms: The test consists of breaking by one blow from a swinging pendulum, under defined conditions, a test piece notched in the middle and supported at each end. Until this European Standard is published reference can be made to the corresponding national or international standards, a list of which is given in annex A. The notch shall be carefully prepared so that no grooves, parallel to 1045-1 base of the notch, are visible to the naked rin.
Learn more about the cookies we use and how to change your settings. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Central Secretariat or to any CEN member. Metal products, mechanical tests, Charpy impact tests, test specimens, testing conditions.
Please download Chrome or Firefox or view our browser tips.
There is no general method for converting the results obtained by one test method into the values which would be obtained by another test method. EN 10Metallic materials — Charpy impact test — Part 2: The test pieces shall be machined all over, except in djn case of precision cast foundry test pieces in which the two faces parallel to the plane of symmetry of the notch can be unmachined. Your basket is empty. The transfer device shall be designed and used in such a way that the ej of the test piece is maintained within the temperature range permitted.
EN Impact Test_百度文库
The reported absorbed energy under these conditions shall be designated 110045-1 the symbols: Accept and continue Learn more about the cookies we use and how to change your settings. Test method V- and U-notches Status: English version Metallic materials — Charpy impact test — Part 1: Customers who bought this product also bought BS EN General, tolerances and deviations.
If standard test pieces cannot be obtained from the material, a reduced section test piece, with a width of 7,5 mm or 5 mm see Table 2 10054-1 be used, the notch being cut in one of the narrow faces.
Method of test; — 100445-1 2: Comparison of results, however, is only of significance when made between test pieces of the same form and dimensions. The energy absorbed is determined in joules. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.
Contents Brief history Foreword 1 Object and field of application 2 References 3 Principle 4 Designations 5 Test pieces 6 Testing machine 7 Test requirements 8 Test report Annex A List of national standards corresponding to the reference European Standard in preparation Figure 1 — Charpy impact test Figure 2 — Configuration of test piece supports and anvils Table 1 — Designations Table 2 — Tolerances on specified test piece dimensions Table 3 — Characteristics of testing machine Table 4 — National standards corresponding to proposed European Standard Page 2 2 3 3 3 3 3 3 5 5 8 6 7 3 4 5 8 Foreword The standard EN 10 concerns metallic materials — Charpy impact test and comprises the following parts: