HT93LC46 DATASHEET PDF

HT93LC46 1k 3-wire CMOS Serial EePROM Features. Operating voltage VCC Read: V~V Write: V~V Low power consumption Operating: 5mA max. HT93LC46 datasheet, HT93LC46 circuit, HT93LC46 data sheet: HOLTEK – CMOS 1K 3-Wire Serial EEPROM,alldatasheet, datasheet, Datasheet search site for. HT93LC46 datasheet, HT93LC46 circuit, HT93LC46 data sheet: HOLTEK – 1K 3- Wire CMOS Serial EEPROM,alldatasheet, datasheet, Datasheet search site for.

Author: Araran Kagaktilar
Country: Sri Lanka
Language: English (Spanish)
Genre: Life
Published (Last): 11 February 2015
Pages: 174
PDF File Size: 4.55 Mb
ePub File Size: 19.26 Mb
ISBN: 391-8-97324-958-1
Downloads: 15809
Price: Free* [*Free Regsitration Required]
Uploader: Zulkik

After power on, the device is by default in the EWDS state. The auto-timing write cycle includes an automatic erase-before-write capability. After the erase-all instruction set has been issued, the data erase feature is activated by the falling edge of H9t3lc46.

When the user selectable internal organization is arranged into 64? Stresses exceeding the range specified under? For successful instructions, CS must be low once after the instruction is sent.

HT93C56-A, HT93LC46, HT93LC46A

At both the power on and power off state the device automatically entered the disable mode. Taipei Sales Office 4F-2, No. Since the internal auto-timing generator provides all timing signal for the erase-all operation, so the SK clock is not gt93lc46. The DO pin will remain low but when the operation is over, the DO pin will return to high and further instructions can be executed. The data on DO pin changes during the low-to-high edge of SK signal.

  BRENT HARTINGER - GEOGRAPHY CLUB PDF

These serial instruction data presented at the DI input will be written into the device at the rising edge of SK.

Since the internal auto-timing generator provides all timing signal for the internal writing, so the SK clock is not required. After the write-all instruction set has been issued, the data writing is activated by the falling edge of CS.

The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential. For the most up-to-date information, please visit our web site at http: However, Holtek assumes no responsibility arising from the use of the specifications described. The information appearing in this Data Sheet is believed to be accurate at the time of publication.

HT93LC46 CMOS 1K 3-Wire Serial EEPROM_百度文库

These are stress ratings only. Its bits of memory yt93lc46 organized into 64 words of 16 bits each when the ORG pin is connected to VCC or organized into words of 8 bits each when it is tied to VSS. Since the internal auto-timing generator provides all timing signals for the write-all operation, so the SK clock is not required. After the data word has been read the internal address will be automatically incremented by 1 allowing the next consecutive data word to be read out without entering further address data.

The HT93LC46 contains seven instructions: Test Conditions Input rise and fall time: By so doing, the internal memory data can be protected. Since the internal auto-timing generator provides all timing signals for the internal erase, so the SK clock is not required. The following are the functional descriptions and timing diagrams of all seven instructions.

  BULA UNAM SANCTAM PDF

The DO pin will remain low but when the operation is over, the DO pin will return to high and further instruction can be executed. By popular microcontroller, the versatile serial interface including chip datasheeg CSserial clock SKdata input DI and data output DO can be easily controlled.

There is an internal pull-up resistor on the ORG pin. Holtek reserves the right to alter its products without prior notification. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise.

Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. The DO pin will remain low but when the operation is over the DO pin will return to high and further instruction can be executed. The 8 bits or 16 bits data stream is preceded by a logical? No data can be written into the device in the programming disabled state.