IEC 60268 7 PDF

IEC SOUND SYSTEM EQUIPMENT –- PART 7: HEADPHONES AND EARPHONES. Buy IEC SOUND SYSTEM EQUIPMENT – PART 7: HEADPHONES AND EARPHONES from SAI Global. IEC Ed. Sound system equipment – Part 7: Headphones and earphones IEC (E), is applicable to headphones, headsets, earphones.

Author: Akinok Mikabar
Country: Kazakhstan
Language: English (Spanish)
Genre: Music
Published (Last): 4 July 2010
Pages: 65
PDF File Size: 8.32 Mb
ePub File Size: 1.9 Mb
ISBN: 702-3-59257-456-1
Downloads: 56959
Price: Free* [*Free Regsitration Required]
Uploader: Maran

FebDecember 17, – 3: Headphones and Earphones is an international standard intended to characterize the performance of headphones and lec. Five separate sequences are provided, each designed to measure specific characteristics.

Search all products by. No – I don’t want to receive the latest audio test information by email. Setup System, Hardware and Calibration Before attempting to run any of the sequences, read the following setup instructions. Learn more about the cookies we use and how to change your settings. 77

A pink noise stimulus is played from the noise speakers and recorded by the occluded ears. Calibrate the microphones per the instructions in the SoundCheck manual. We use cookies to make our website easier to use and to better understand your needs.

You may experience issues viewing this site in Internet Explorer 9, 10 or Marking, Microphones, Audio systems, Ratings, Designations, Instructions for use, Headphones, Classification systems, Frequency response, Earphones, Audio 60628, Voltage measurement, Impedance measurement, Testing conditions, Preamplifiers, Idc tests, Acoustic measurement, Electrical wave measurement, Electrical properties and phenomena, Acoustic testing.

This value is converted to dBV and used to calculate the IM and difference frequency stimulus levels.

BS EN – Sound system equipment. Headphones and earphones

The sequence uses a stepped sine stimulus to measure frequency response, THD and impedance, a composite signal of 70 Hz and Hz with an amplitude ratio of 4: This sequence uses a pink noise stimulus to characterize the passive, active and total attenuation of noise cancelling headphones.

  KASPAROV CARO KANN PDF

You may find similar items within these 6068 by selecting from the choices below:. Take the iiec route to manage medical device 600268. Matthew Miller November 15, – 6: It can also be used to characterize the passive attenuation only of a standard non-ANC headphone.

There are several unique Signal Paths used in the sequences which are not a part of the default SoundCheck installation. Registration required The content you have requested is available only to registered visitors. Sound System Equipment — Part 7: Worldwide Standards We can source any standard from anywhere in the world.

The sequence prompts the operator to enter the rated voltage 6268 rated impedance of the DUT. It is recommended that the sequences be run directly from the IEC folder. The content you have requested is available only to registered visitors.

IEC Headphone Sequences – Listen, Inc.

First, a pink noise stimulus is played from the noise speakers and recorded by the unoccluded ears. The data from each loop iteration is displayed as it is acquired.

If the answer is Yes, the user is prompted to turn the ANC on and the sequence repeats the passive measurements. Connect the impedance boxes between the headphone amp out and headphone input. Calibrate the headphone amplifier channels per the instructions in the SoundCheck manual. It then enters a loop which will run 5 times.

A series of post-processing steps follow to apply the weighting and correction curves, calculate the LAEQ and then the Simulated Program Characteristic Voltage is calculated along with the Hz voltage sensitivity. Hardware Requirements In order to run the sequences, the following ic is required: This sequence satisfies the requirements of Section 8. The user is first prompted to enter the rated voltage.

  DEADLANDS BLOODY OL MUDDY PDF

The play and record acquisition takes place 3 times and the user is prompted to reposition the DUT on the HATS in between acquisitions. Crosstalk and radiation curves are then shown on the final display. You are ready to start 660268 sequence. It then calculates the voltage required to produce 1 iiec into the rated impedance. Relink dialog Here is a list of sequences and their default signal paths unique paths are in bold: If passive, connect to the headphone amp or separate audio power amplifier You are ready to start the sequence.

BS EN 60268-7:2011

In order to add these Signal Paths to your System Calibration or relink to existing Signal Paths, you should open each of the sequences individually and, if prompted, add or relink Paths to your System Calibration. This approach provides the iiec with the flexibility to measure all or some 602268 the characteristics of their headphone. Headphones and earphones Status: Your basket is empty. The sequence first plays a stepped sine through both channels of the DUT and captures the sound radiation from the DUT using 2 reference mics.