THE TEMPLATE FOR THE ENTIRE PLINTH IS ALL. ON THIS PLINTH. FOR LENCO L 75 TURNTABLE YOU WILL NEED TO DO TWO THINGS TO THE L Used Lenco Plinth for sale on + second hand hifi sites & shops. Hand Made Solid Mahogany Wood Plinth For Lenco L75 Turntable Czech Republic eBay. “The Lenco doesn’t need a plinth in order to be Great, it is inherently Great. The plinth just brings it to a higher level. If you were to buy a Lenco.

Author: Disho Milkis
Country: Barbados
Language: English (Spanish)
Genre: Software
Published (Last): 3 September 2015
Pages: 248
PDF File Size: 17.97 Mb
ePub File Size: 11.75 Mb
ISBN: 849-3-47732-170-1
Downloads: 17333
Price: Free* [*Free Regsitration Required]
Uploader: Vojinn

Pulling off the platter including spindle takes loosening of the spindle locking l755. First of all, a wealth of information on the Lenco L75 can be found here at Lenco Heaven. Dust cover has scratches but no cracks. I ,enco tried out my stock mats, an old Thorens which I use for thea 3 mm kork mat and a 3 mm silicone mat. I could then take mine apart to see how mine is set up. In the long run you will save yourself some frustration and end up with a much improved piece of audio equipment.

Haaah, I tend to like my free-skiing skis light and with a lot of feedback, and my race skis damp, quiet, and stable – but my turntables are a different story. Werner wer – just my initials, not a nick! A perfect match for the vdh cartridges. Member Member Offline Location: It’s all together now!

July 23, I’m not at home just now but will post a photo when time and beer allows.

pkinth The magnetic damping of the counter balance is excellent. Here is what it looked like with my replacement platter mat on it: Few other useful tips here in: The entire plinth seen from top. Top plate damped with 4 mm bitumen pads. I only have three, and can’t spare them at the moment!


Used lenco plinth for Sale |

I used sand paper and acetone to clean off any residual paint. Hello, This probably not very helpful and from a very vague memory. Administrator Member Offline Age: Metal sheets glued to the rear of top plate with Araldite. I am starting this project with a heavy platter Lenco L75 that I have just started using for 78 lnco playback, that was pinth very low usage turntable – almost a new-old-stock assembly to re-plinth.

Lenco Plinths

For the meantime I would like to keep the existing plinth as I prefer lenci look of it to some of the bespoke plinths I’v seen. Another fellow set up a Rega tonearm in the original hole despite improper geometry and VTA as I did for a long whileset it up on bricks with no plinth whatsoever, and reported this combo easily beat his maxed-out Linn LP However, if the rear left spring is weak or missing there’s a risk that the baseboard is pushing up under the motor and that would affect the drive.

plinyh To be continued next year as I’ll do the my own and Michael’s top plates and have them all spray painted at the same time. If it’s crumbling, shove some cotton wool in there, but don’t pack too much in – or you’ll give the plinth a hard ‘sports’ suspension! Three times filler and sanding leaves a smooth surface ready for spray paint. Made from HQ plywood, veneer zebrawood and is covered with natural oil of penco highest quality.


Is your plinth like the photo below, with the two rear plinth-suspension springs arrowed? Thus, all things point to an easy rebuild and google can present us with an abundant amount of inspiration on a new plinth. Once the suspension is defeated, then a plinht platform does a lot to further improve the sound.

Before buy, check out the images I changed to an AT92ecd cartridge potted in a metal holder, stuffed with my own formulation of damping compound, and now I have dispensed with the sorbothane feet. Before buy, check out the plinthh in the google what you want to buy. Member Member Offline Location: The – almost – finished turntable I made a thin panel for covering the former tonearm holes but it didn’t look good.

Look here for details. Thus, some day I’ll take the whole thing apart, sand the top plate and fill the holes with a metal filler and have it spray-painted by a professional.

Some day we’ll get these top plates done; filling the holes with metal filler and have them spray painted by a professional. Put rubber feet on the corners of the plinth frame; or board-over the base and put rubber feet on the board. This Made in Swiss Turntable was created before Good looking build Chris. Also shop in Also shop in.

Werner wer – just my initials, not a nick! The paint used by Lenco for these turntables really wasn’t good and is easily removed. Suggest a ‘swop things around a bit to see if it helps’ session.