View and Download Kawasaki Ninja R service manual online. Ninja R Motorcycle pdf manual download. Also for: Ninja er-6f, Ninja er-6f abs. Visit Kawasaki Motor Corps., USA owners center for up to date service manuals, parts diagrams, ROK™ info, owner support, warranty info, Kawasaki Protection. Ninja R. ER-6f. ER-6f ABS. Motorcycle. Service Manual. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system, or.

Author: Balkis Yogul
Country: Bhutan
Language: English (Spanish)
Genre: Art
Published (Last): 17 December 2007
Pages: 258
PDF File Size: 3.40 Mb
ePub File Size: 15.90 Mb
ISBN: 476-8-49274-660-4
Downloads: 1207
Price: Free* [*Free Regsitration Required]
Uploader: Kera

Align the white paint of the reserve tank over flow hose with the welding bead. Do not use any other battery except for a 12 V sealed battery as a power source.

This is 50 mm 2.

Such a shock to the water temperature sensor can damage it. Page Newly activated sealed batteries require an initial charge.

Owner’s Manuals & Service Manuals | Kawasaki Vehicles

Such a shock to the ECU can damage it. Vacuum Pressure Absolute to Sensor Vv: If any wiring is poor, replace the damaged wiring. Clamp Faces the stopper forward.

Special Tool – Clutch Holder: Service Code 51, 52 Stick Coil 1: If the corrugated fins [A] are deformed, carefully straighten them.

2007 Kawasaki Ninja 650R — Owner’s Manual

Turn Signal Relay 9. Clamp Install the clamp with the quick rivet onto the throttle body assy. Before replacing a blown fuse, always check the amperage in the affected circuit. Page Page Page – Air switching valve service code Page – Oxygen sensor heater service code Throttle Cable Accelerator 3.


Such a shock to owers part can damage it.

If whitish cotton-like wafts are observed, aluminum parts in the cooling system are corroded. Stick coil shorted or not in good contact Inspect or Reinstall see chapter Main Fuse 30 A 6. If there is any doubt as to the condition of the reeds, re- place the air suction valve as an assembly. manuall

Do not use fluid from a container that has been left unsealed or that has been open for a long time. Starter Relay Lead 4.

Clamp Hold the clutch cable. Steering Stem Bearing Driver Adapter, Apply soap and water solution or rubber lubricant. Turn iwners ignition switch OFF. ABS Hydraulic Unit 4. Place a strip on each journal parallel to the camshaft in- stalled in the correct position. Comments to this Manuals Your Name.

Brake Pipe from Front Master Cylinder 5. Windshield see Windshield Removal in the Frame chapter. Al- though no adjustments are required, a thorough visual in- spection must be made at the intervals specified by the Pe- riodic Maintenance Chart. If the seal is torn or is leaking, replace the bearing. Place the air cleaner drain hose end as shown in the figure. Valve Seat Cutter Holder Bar: Air Cleaner Housing 9. Torque – Swingarm Pivot Shaft Nut: Front Fork Oil Seal Driver: Water-proof Joint D 3.


Hold the subthrottle valve actuator lead. Clutch not disengaging Engine oil level too low Shift fork bent or seized Engine oil poor quality or incorrect Gear stuck on the shaft Gauge incorrect Bands Hold the main harness between the frame pipe and fuel tank bracket. Stick coil trouble Inspect see chapter Sealant – Three Bond: Be sure to maintain proper alignment and use smooth movements when installing. Torque – Fuel Level Sensor Bolts: Spark plug dirty, broken or gap maladjusted Inspect and replace see chapter 2.

Avoid sharp bending, kinking, flattening or twisting. Such a shock to the sensor can damage it.

Reserve Tank Over Flow Hose 4. Apply silicone sealant to the portions [E] on the upper crankcase half, and insert [F] the new oil plug until it is bottomed.