Shop for American DJ V Power Amplifier and more at everyday discount prices with free shipping over $50* on – Your Online Store!. Buy the ADJ V Amplifier at PlanetDJ. Low VIP Pricing, Financing and Free Shipping available. American Audio | V | User manual | American Audio V User manual American Audio┬« – – V Vplus Series Amplifiers Power.

Author: Toshura Telrajas
Country: Spain
Language: English (Spanish)
Genre: Sex
Published (Last): 25 June 2004
Pages: 375
PDF File Size: 18.80 Mb
ePub File Size: 6.2 Mb
ISBN: 189-3-90346-546-2
Downloads: 23545
Price: Free* [*Free Regsitration Required]
Uploader: Muzilkree

American Audio V3000/V2000 Stereo Amplifier User Manual

Every V Vplus series amplifier has been thoroughly tested and has been shipped in perfect operating condition. Cooling Fan – This is a dual speed cooling fan. The limiter reduces the average output level when the signal begins to distort, this process is designed to reduce distortion and protect the speakers. When the channel goes into protect mode all output for that channel will turn off. Channel 2 Frequency Adjustment.

American DJ V3000 2 Channel Professional Stereo Amplifier

When dip switches 2 and 3 are in the “ON” the filter will cut off frequencies at and below 30Hz, when these dip switches are in the “OFF” position the filter will cut off frequencies at and below 50Hz. This may reduce the buzz that is caused from an electrical 60Hz cycle. Each channel operates independently of each other allowing each channel to have different filter ameriacn.

After inserting the wire into the binding post hole, screw the binding post cap down on the wire. Apply an input source signal to your amplifier.

Fuse Holder – This holder houses the external fuse. This light may continue to glow briefly after main power has been turned off, this is normal.


To reset the breaker, push it in. The appliance has been exposed to rain or water. Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Use these connections to connect the americn signal from a mixer, cross-over or EQ to your V Vplus series amplifier.

If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes. Service Hours are Monday through Friday 9: Check the line from the output terminal of the amplifier to the speaker.

American Audio Stereo Amplifier V/V User Guide |

Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. Use your front gain controls to regulate the output volume.

Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit. Bridged-Mono Mode Caution – The voltage across the output terminals of a bridged V Vplus series amplifier may equal or exceed volts RMS and may be as aamerican as volts.

Channel 1 Frequency Adjustment. This fans are used to cool the internal parts of the amplifier when in use.

The fixture does not appear to operate normally or exhibits a marked change in performance. Insert the spade connector in to the binding post and tighten the caps down on the spade connector. Ground Lift Switch – This switch is used to disconnect the internal ground signal from the amplifier chassis ground. This booklet contains important information concerning the proper and safe operation of your new amplifier.


Be sure that your front gain controls are turned down to their lowest level full counter-clockwise. Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. If your speaker lines short, the amplifier automatically detects this problem and discontinues operation for that channel.

When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction. Fuse Holder – 10 5 11 6 12 1 Diagram 3 This holder houses the external fuse.

V Power Amplifier by American Audio Valuation Report by

Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable. Power Switch – This switch controls the units main power. This LED may glow when the unit has been turned off, this is normal. Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. These fans are used to cool the internal parts of the amplifier. Use channel two positive output terminal for the negative connection and the channel one positive output terminal for the positive connection.