ASME BPE 2007 PDF

ASME BPE (Revision of ASME BPE). Bioprocessing. Equipment. AN AMERICAN NATIONAL STANDARD. Three Park Avenue. Buy ASME BPE Bioprocessing Equipment from SAI Global. No reproduction may be made of this material without written consent of ASME. ASME BPE (Revision of ASME BPE) Bioprocessing.

Author: Akigrel Basho
Country: Solomon Islands
Language: English (Spanish)
Genre: Medical
Published (Last): 3 July 2006
Pages: 317
PDF File Size: 5.85 Mb
ePub File Size: 7.75 Mb
ISBN: 887-3-29589-345-5
Downloads: 49480
Price: Free* [*Free Regsitration Required]
Uploader: Gok

The use of short welding ferrules should be incorporated into the design. Cotter, Cotter Brothers Corp. If piping support is required within a classified space, a hygienic support system shall be used. All surface coatings shall remain intact and 10 SD When markings are required on process contact bppe, other methods of identification should be used. See illustration in Table DT for the proper orientation.

ASME BPE Bioprocessing Equipment_图文_百度文库

MacDonald, United Association D. In addition to fittings, this Part also covers the tolerances and marking of commercial stainless steel process components including, but not limited to, tubing, vessels, valves, pumps, filter housings, and instrumentation. Some examples of polymers are ame, proteins, DNA, and dendrimers.

Mathien, Plymouth Tube Co. Methods of separation used in industry are a removable spool piece b U-bend transfer panel c double block-and-bleed valve system see Fig.

Preferred hygienic support design shall incorporate rounded geometry to facilitate draining and cleanability, with minimal potential for the collecting and retaining of dust and residual cleaning solution or spillage on the hanger. Ra Readings for Product Contact Surfaces. Asmw Redesignated as Fig. Asmw then provides for a continuous solution sheeting over the lower surfaces.

  BS EN 50174 PDF

Recommended Flow Rates to Achieve 5 fps asem. Recommended tolerances are per Table SD-7 and Fig. Pipe sizes should be specified to guarantee adequate supply and pressure to the spray devices. Colors may range from pale bluish-gray to deep blue, and from pale straw color to a black crusty coating.

Acceptance Criteria for Tube-Attachment Welds. If a branch from a primary pipeline has demonstrated flow during cleaning and sterilization, it does not constitute a dead leg.

The equipment may or may not perform the loading and unloading of the works. All internal instruments shall be installed e. It shall be the responsibility of all parties involved to adhere to the concepts of this Part as they apply to advance the knowledge and database for sterilizable and cleanable equipment and systems.

Food and Drug Administration U. Mount Nominal Size mm The distance H of the physical break should 20007 at least twice the inner diameter of the hoses, drain valves, or any other component leading to drains or sinks to avoid back siphoning into the POU assembly.

0207, Abbott Laboratories E. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk vpe infringement of such rights, is entirely their own responsibility.

Daly, Jacobs Engineering J. GTAW may be performed by adding filler material to the weld, or by a fusion process in which no filler is added.

ASME BPE Guidelines for Pharmaceutical Equipment

The target ratio may not be achievable for weir-type valves clamped to tees and certain sizes of close welded Point-of-Use valves, as shown in Fig.

  CP2K TUTORIAL PDF

Short Outlet Reducing Tee. Recommended b Typical Hygienic Clamp Union 0207 1 in. When an application is covered by laws or regulations issued by an Enforcement Authority e. Kettermann, Rath Gibson K. Double Block-and-Bleed Valve Assembly.

Zinkowski, Vice Chair P. Stover, NewAge Industries, Inc. Elbich, Exigo Manufacturing M. Williams, Piping Systems, Inc. The committee met in and there was consensus concerning the need to develop standards that would meet the requirements of operational bioprocessing, including: For nominal metric size tubing and fittings, refer to the appropriate international standards.

Flow Rate mm gpm 12 16 24 31 39 to to to to to 14 19 28 38 47 Lpm 45 60 90 to to to to to 53 72 1, 1, Flow rate p 2. They can be synthesized either through chain reactions or by templating. Rau, Dockwelier AG B. Dvorscek, Abbott Laboratories G. Newman, Newman Sanitary Gasket Co.

Sedivy, Rath Manufacturing C. This Part establishes design guidelines applicable to bioprocessing equipment, components, assemblies, and systems. This Part describes the fittings made for use with nominal outside diameter O.

Arnold, Pall Filtration Pte. Klemp, Advance Fittings Corp.