ASTM A593 PDF

we manufacture one of the widest ranges of ASTM A Fasteners. Exporter of a wide range of ASTM A Fasteners in India at Best Factory lized. or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. This specification for ASTM F covers the requirements for stainless steel bolts , hex cap screws, and studs to in., inclusive, in nominal diameter in a.

Author: Disho Basida
Country: Turkey
Language: English (Spanish)
Genre: Medical
Published (Last): 11 August 2005
Pages: 69
PDF File Size: 15.55 Mb
ePub File Size: 15.22 Mb
ISBN: 502-4-69812-389-8
Downloads: 2571
Price: Free* [*Free Regsitration Required]
Uploader: Akimuro

B legend of conditions: Hex head, square head and hex socket cap screws. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4. A Minimum values except where shown as maximum or as a range.

Z593 A tests should be made whenever feasible.

Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed in accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties. Special fasteners have full size heads shall be tested as specified for stud bolts and other bolts.

A Tensile stress areas are computed using the following formula: AF – Headed and rolled from annealed stock and ast, reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. ASTM F covers seven groups of stsinles steel alloys, including twelve austenitic, two ferritic, four martensitic and one precitipitain hardening. CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

ASTM F Specification – Boltport Fasteners LLP

Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including heading and threading has been completed. Special fasteners have full size heads shall be tested as specified for stud bolts and other bolts. E When approved by the purchaser, alloy F may be furnished. AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming.

  ICTAD SPECIFICATION PDF

SH – Machined from strain hardened stock or cold worked to develop the specific properties. Hex head, square head and hex socket cap screws. A Tensile stress areas are computed using the following formula: A Where options are given, all the tests under an option shall be performed.

SH – Machined from strain hardened stock or cold worked to develop the specific properties.

B legend of conditions: A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed. B Tests that are not mandatory C Special fasteners are those fasteners with special configurations including drilled heads, reduced body, etc.

ASTM F593 Specification

F When approved adtm the purchaser, alloys or Se may be furnished. C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming.

A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4. B Tests that are not mandatory C Special fasteners are those fasteners with special configurations including drilled heads, reduced body, etc.

  COURS DE MICROPROCESSEUR 8086 PDF

A Minimum values except where shown as maximum or as a range. D Yield strength is the stress at which an offset of 0. F When approved by the purchaser, alloys or Se may asfm furnished. CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

Free Technical Information

C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F A Where options are given, adtm the tests under an option shall be performed.

D When approved by the purchaser, alloysSe, or XM1 may be furnished. Option A ashm should be made whenever feasible. This specification covers the requirements for stainless steel bolts, hex cap screws, and stud bolts in imperial size 0. E When approved by wstm purchaser, alloy F may be furnished. D Yield strength is atsm stress at which an offset of 0. D When approved by the purchaser, alloysSe, or XM1 may be furnished. A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed.

Please find below chemical, mechanical, supply condition, heat treatment, marking and other requirements on Stainless Steel Bolts. AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.