ASTM F2329 PDF

Zinc Coating Thickness Requirements: ASTM A vs. F Dimension. ASTM A ASTM F Avg. Coating. Thickness of. Specimens. Tested. ASTM F covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special. ASTM A does not cover threaded bolts and fasteners. ASTM A and F are the ASTM specifications that cover the requirements for.

Author: Dour Kazrashura
Country: Lebanon
Language: English (Spanish)
Genre: Love
Published (Last): 20 December 2008
Pages: 300
PDF File Size: 14.67 Mb
ePub File Size: 9.29 Mb
ISBN: 561-3-59316-154-6
Downloads: 41820
Price: Free* [*Free Regsitration Required]
Uploader: Migul

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. In case the geometry of the specimen does not permit? Baking shall be conducted after pickling and prior to hot-dip galvanizing.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Best practice is to note the bath temperature when galvanizing steel to F, although only the average bath temperature is required. It is intended to be applicable to fasteners that are centrifuged or otherwise handled to remove excess zinc. Afif — The difference between hot dip galvanizing structural articles and fasteners is the spinning.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Spinning removes excess zinc from the fastener so that the nut will mate with the bolt.

The average of those selected measurements is the average coating thickness. Also in which material we are coating atm galavanizing. Minor roughness that does not impair the intended use of the part, or roughness that is related to the uncoated surface condition of the part, shall not constitute grounds for rejection of the parts.

Electroplating is an entirely different process and is a much thinner coating.

Rob- Tensioning the bolt will not adversely affect the galvanizing. We are are not certain what standards are commonly used in Dubai, so atm cannot speak to those. When requested by the purchaser, the average galvanizing temperature that the fasteners will be subjected to shall be furnished. Nails and rivets are not included in this speci?

  JENBACHER J920 PDF

April 10, Authored by Bernardo A. The information provided herein is not intended as a representation or warranty on the part of the AGA.

All inspections and tests shall be made at the place of manufacture prior to shipments, unless otherwise speci? The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. This abstract is a brief summary of the referenced standard. D Visual inspection for conformance.

ASTM F2329 vs. ASTM A153

If you are concerned about the hardness dropping, you could look at alternatives platings that do not require heat, like mechanical galvanizing. The number of specimens to be tested per order shall be as speci? Smoothness of a surface is a relative term. Thus, the thickness determined is a point value.

B For test method, see The coating thickness requirements of A Table 1 meet or exceed those of F Table 2 except for: There are three columns listing the number of test articles for three different inspection tests required under F This process involves the removal of excess zinc by spinning the parts in a centrifuge, or brushing the threaded portion, or handling otherwise to remove the excess zinc.

Hot-Dip Galvanizing Specifications – Portland Bolt

Materials and Manufacture 5. The test methods for appearance and smoothness under F shall be conducted for every batch lot by visual inspection in accordance with methods provided in A According to Note C of Table 1, It is only required to conduct testing on samples for coating thickness once every five batch lots. If the galvanizing process is carried out at a higher temperature than the stress relief or the tempering temperature of the fasteners, than the purchaser shall make provision for mechanical testing.

Parts may be dull due to the presence of silicon in the steel. Rejection and Rehearing Each bolt specification may list additional asttm to prevent hydrogen embrittlement as well as place additional requirements on embrittlement testing which should be researched separately.

  FORMULAIRE IMM 1295 PDF

F defines the two different lots and their associated sampling plans as follows: Threaded fasteners are handled differently in order to remove the excess zinc from the threads and would fall under A or F A touches on threaded fasteners, but is not fastener specific. The material provided herein has been developed to provide accurate and authoritative information about after-fabrication hot-dip galvanized steel.

This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and wstm threaded fasteners applied by the hot-dip coating process.

The selection of the sampling plan shall be in accordance with Guide F In addition, small parts shall be air cooled as needed in order to prevent the formation of zinc oxide.

If the customer specifies, the galvanizer will be required to provide the average galvanizing temperature the fasteners will be exposed to. Average Thickness of Individual Specimen 0. Fasteners which are subjected to severe work hardening must be stress-relieved prior to galvanizing. In the case of a fully threaded rod, the thickness measurements shall be determined at each end of the article. Your email address will not be published.

The coating thickness requirements of A Table 1 meet or exceed those of F Table 2 except for:.

Hot-Dip Galvanizing Specifications

Portland Bolt performs hot dip galvanizing of threaded fasteners within our 85, square foot manufacturing facility. Many thanks Sal from Dubai. This method is similar to an inspection of coating thickness on multi-specimen articles galvanized per ATSM A Furthermore, there are two types of production lots: This specification covers the requirements for hot-dip galvanizing on iron and steel products made from rolled g2329 and forged shapes, castings, plates, bars, and strips.