Designation: F /F M â 07 Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This. ASTM F/FM: Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series. Designation: F /F M – 05 Standard Speci?cation for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This.
|Published (Last):||27 December 2009|
|PDF File Size:||19.94 Mb|
|ePub File Size:||3.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
Voids are produced by marks or impressions of chips shear burrs or by rust formation on the raw material. NOTE 1Forging cracks within the limits of this specification may beunsightly, but do not affect the mechanical properties or functionalrequirements of the bolt. It is informational only and not an official part f78 the standard; the full text of the standard itself must be referred to for its use asrm application. Limits are specified in5.
Current edition approved Oct. NOTE 1—Forging cracks within the limits of this speci? ASTM B – Supplementary Requirements shall in no way negate anyrequirement of the specification itself.
Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other. This specification covers metric series products with nominaldiameters of 4 mm and larger and with specified minimumtensile asrm of MPa and higher; and inch seriesproducts with nominal diameters of No.
The valuesstated in each system are not exact equivalents, therefore, eachsystem must be used independently of the other.
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. ASTM A – Typical tool marks are shown in Fig. This abstract is a brief summary of the referenced standard.
ASTM-F/FM-, 0 –
A number in parentheses indicates the year of last reapproval. ASTM A36 – This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs, including heat-treated machine screws, tapping screws, and sems. Typical tool marks are shown in Fig. Supplementary Requirements shall in no way negate any requirement of the speci?
If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.
Enter your personal account email address to request a password reset: Shear bursts may also occuron the sides of hex-head wstm. Get astm e94 for free from our online library: No items in asttm. If you like to setup a quick demo, let us know at support madcad.
There were no books found for the applied search filters. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
There are no ISO standards for surface discontinuities f788 any inch-series products. This specification covers metric series products with nominal diameters of 4 mm and larger and with specified minimum tensile strengths of MPa and higher; and inch series products with nominal diameters of No. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the aboveaddress or at phonefaxor service astm. They are not planished during forging.
The section shall be etched for microscopic examina-tion in accordance with Test Method E Copyright Compu-tecture, Inc.
ASTM F788 – 13(2018)
For metric series products, D and Dc are in millime-tres; for inch-series products, D and Dc are in inches. NOTE 2Bursts and shear bursts within the limits of this specificationmay be unsightly, but do not affect the mechanical properties or functionalrequirements of the bolt.
FORMAT Single User Subscription 7f88 License Subscription BOOKS All Astk PACKAGES All Packages EDITION to PUBLISHER. Typical shear bursts are shown in Fig.
NOTE 2—Bursts and shear bursts within the limits of this speci? Historical Version s – view previous versions of standard. Combiningvalues from the two systems may result in nonconformancewith the specification. There are no ISO standards for surfacediscontinuities on any inch-series products. Current edition approved Nov. Visual inspection can include the use of devices that provide up to, and including, power magni? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Typical shear bursts areshown in Fig. Acceptance shallbe based on the requirements of S1.
This standard has been approved for use by agencies of the Department of Defense. Bolt astm a pdf – astm a pdf Bolt astm a pdf Bolt astm a pdf Limits are specified in 5. Combining values from the two systems may result in nonconformance with the specification.