epD‐BfS‐ () Environmental Product  Schweizerischer ingenieur‐ und Architektenverein (SiA). () Merkblatt energieausweis für Gebäude gemäß Sn en und Sn en zurich.  Schweizerischer . Flash point: > 21° C „Beschichtung auf Zink und verzinktem Stahl“ from Bundesausschuss Farbe und Sachwertschutz (BFS) according to Merkblatt 5 of BFS. Flash point: > 21° C. Solid substance: approx. 55% Zinc and galvanized surfaces are to be prepared according to Merkblatt 5 of. BFS. Clean the surfaces to be painted and remove dirt of all kinds, including dust, mortar droppings, and similar.
|Published (Last):||18 February 2004|
|PDF File Size:||13.82 Mb|
|ePub File Size:||7.88 Mb|
|Price:||Free* [*Free Regsitration Required]|
Possibly a second finishing coat may be necessary.
Material Properties Water-dilutable, ecologically compatible, low odour. Do not breathe spray dust. Fibre-reinforced, plasto-elastic compound for applying pigmented intermediate coatings and suitable for embedding of reinforcement fabric.
Two coats are necessary to obtain an adequate protection against algal and fungal attack.
We will describe appropriate working methods, if a substrate not specified above is to be coated. Modelling intermodal travel in Switzerland: Prime chalking, sanding, absorbent surfaces with AmphiSilan-Putzfestiger.
Transport Planning – Theory and Models. Thus all relevant copper surfaces must be protected against oxidation. Thus all relevant copper surfaces must be protected against oxidation. In case of direct reworking, all traces of additives must be pre-wetted and completely removed after a short reaction time. Clean existing renders by suitable means. Apply Cap-elast Phase 1, diluted approx.
Big Data Transport Models Using data traces to improve transport systems. Harmful to aquatic life with long lasting effects.
ThermoSan NQG Nespri-TEC
An additional priming coat of CapaGrund Universal must be applied. Always use tinted paint of same batch, when applying on seamless surfaces. German committee dealing with paint and protection of real properties Gloss Level Matt flat G 3 Storage Keep in a cool, but frost-free place.
Brilliant, intensive colours may have a lower opacity. Minimum drying time between coats: While discrete-choice models and in particular mode-choice models are widely used to study how people react to specific changes in the system, little published research exist that analyses the possibilities and pitfalls of pairing mode-choice models with the traffic simulation inside of an iterative process.
Observe a minimum drying time of 12 hours between coats. Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels.
Do not empty into drains, water courses or into the ground. Determine the bfx amount of material required by coating a test area on site. Open defective, cracked joints approx. By eliminating the need to sample alternative paths for estimation, it also simplifies the estimation process, making it a viable choice as an integral solution for joint route and mode choice modelling.
Technical Assistance As it is impossible to list herein the wide variety bfe substrates and their specific problems, please request our technical assistance in case of queries.
ThermoSan NQG Nespri-TEC: Caparol
Checnet Coupling human and ecological networks for sustainable landscape and transport planning. Allow the reinforced area to dry thoroughly. Do not eat, drink or smoke while using the product. Repairs must have adequate time to cure and dry. Technical information Technical Information No. Only frost-resistant bricks or clinkers free of foreign bfe are suitable for coats of paint.
Tinting may cause bfd in the technical characteristics. Remove salty efflorescence by dry wire brushing. This product bfx provided with a preservative against deterioration in the coating film due to algae and fungal attack for prolonged – but not merkboatt – protection, depending on the degree of moisture and intensity of organic infestation.
Use P2 dust filter for grinding. Technical information Technical Information No. Axhausen, Kay W Particular attention should be made to removing wastage from site in compliance with standard construction site procedures.
Facing Brickwork with Joint Cracks: Depending on atmospheric humidity, temperature and layer thickness. Allow to dry, then apply one intermediate coat of Cap-elast Phase 1 to the full surface, tinted to match the finishing coat in shade approximately.
Also suitable for the protection of substrates against environmental effects and aggressive airborne pollutants.