You are here: Home · User Manuals · Inverters and Energy Recovery · Operating instruction; ACU Operating Instructions Frequency Inverter V / V. The safety instructions and information on use in this documentation must be Please note, that Bonfiglioli Vectron does not take any responsibility for the. 02/ Operating Instructions Agile. 3 Please note, that Bonfiglioli Vectron does not take any responsibility for the compatibility of external products (e.g.

Author: JoJojinn Zusar
Country: Chad
Language: English (Spanish)
Genre: Business
Published (Last): 13 May 2009
Pages: 385
PDF File Size: 15.95 Mb
ePub File Size: 16.8 Mb
ISBN: 852-3-12277-756-7
Downloads: 60928
Price: Free* [*Free Regsitration Required]
Uploader: Nalmaran

Parameter Adjustment is used for this purpose. Division marks The number of increments of the connected speed sensor can be adjusted via the parameter Division marks speed sensor 2 These settings are aimed at one master serving all the channels.

Active Series

This completes the adjustment of the analog input. Plug the EM-IO expansion module 2 onto the slot 3. In this way, both frequency inverters can be operated synchronously via the remote control. The definition of the analog input characteristic can be calculated via the two-point form of manul straight line equation. The fundamental tasks of the master are controlling the start of the network boot-up sequencegenerating the SYNC telegram and evaluating the emergency messages bonviglioli the slaves.

If not, faulty measurements and settings can result. An exchange of data can only be implemented by the master via a client SDO. Application manual The application manual supplements the documentation for purposeful installation and commissioning of the frequency inverter.

Configuration – Field-oriented Control, Speed Controlled The instructions must have been read and understood before starting work at the device. Via the parameter Amplification the amplification can be set as a percentage of the final value of the analog output 10 V. No connection work may be performed, while the system is in operation.


The interval for the SYNC telegram of a frequency inverter defined as the system bus master is adjustable.

The zero adjustment with the parameter Offset is done specific to the application as a percentage of the final value of the analog output 10 V. Unauthorized opening and improper interventions can lead to physical injury or damage to property. The setting of the operation mode is done via the following parameters: If a fault switch-off occurs on a number of slaves, the first slave to transmit its emergency telegram is displayed on the system bus master.

L1 L2 L3 1. F – Characteristic If a further fault occurs subsequently, it is transmitted in a new emergency telegram.

Motor Circuit Breaker The data type uint, int, long are exchanged in a telegram. A repeat start of the drive mechanism is possible by switching the start signal bonfilgioli and off if the fault has been cleared beforehand.

Pipe conveying Screw conveyor.

Examination before installation Every inverter has been fully tested and examined before shipment. The pluggable sockets of the expansion module enable economical overall fitting with a safe function. Bulk long distance conveying Overland conveyor. Vertical conveying Bucket elevator. For each frequency inverter, the set time for the transmission interval e.

Pulse Width Modulation If the set holding time has expired, there is a fault message. The telegram contains two data bytes.

Further, there can be access to the parameterization of all the frequency inverters on the system bus by means of a field bus connection via the client SDO of the master frequency inverter. If a timeout period is exceeded, the bonfiblioli inverter breaks down and reports one of the faults: Phrakanong-nur, Wattana, Bangkok Tel.


Run mode signal 2.

Bonfiglioli Vectron Syn10 S115 01 Operating Instructions Manual

Comments to this Manuals Your Name. Damaged or destroyed bonfiglioi may not be put into operation because they may be a health hazard. For parameter analog modethe additional operation mode 4 — abs. Resolver input, encoder emulation output 3 channels1 analog input Optional PC software VPlus for Windows with setup, terminal monitor, actual value window, and scope function Accessories: This manual also for: For better clarity, the user documentation is structured according to the customerspecific demands made of the frequency inverter.

Description Minimum mznual percentage Maximum reference percentage 54 Min. The behavior can be parameterized for each PDO channel.

Bonfiglioli act Manuals

Remember to turn off power supply and wait till the Power LED goes off before proceed. If the input signal is less than 1 V or 2 mA, there is a warning message. The selection depends on the selected configuration and control procedure.

The control signals are set to the logical value zero as a function of the selected operation mode.

The frequency inverter defined as a system bus master automatically generates the correct telegrams. The display of the digital input signals enables checking the various control signals and their connections with the software functions in question, mannual particular in commissioning. The following examples show the application-specific adaptation for an analog voltage signal.