CQI-15 WELDING SYSTEM ASSESSMENT PDF

Welding System Assessment (CQI). Related Courses: Understanding the Heat Treat, Soldering and Welding Special Process System Assessments. Program. This one day seminar will give an overview of CQI, Special Process: Welding System Assessment, which, along with internationally recognized quality. Documents Similar To CQI Welding System Assessment. VDA Minimizing Risks in the Supply Chain. Uploaded by. Sergio Boillos. AIAG Cqi 14 Warranty Key.

Author: Gardalmaran Bazshura
Country: Estonia
Language: English (Spanish)
Genre: History
Published (Last): 25 November 2004
Pages: 195
PDF File Size: 12.91 Mb
ePub File Size: 8.8 Mb
ISBN: 715-7-33553-775-7
Downloads: 54334
Price: Free* [*Free Regsitration Required]
Uploader: Fekazahn

Camar Aircraft Products Co. Nonconforming Product — Product that does not conform to the customer requirements.

CQI Welding System Assessment_百度文库

Company Quality Manual Document No. Parts shall be taken from the shipping axsessment at the dock or the end of the welding operation.

These alarms and safety alarm checks being shall be individually tested at the required frequency as tested at the required listed in the control plan, and after any repair, process frequency or after any repair or change or rebuild.

The organization shall identify who is responsible for performing these tasks. Section 2 — Floor and Material Handling Responsibility? Page 1 of 57 Review performed More information. The facility shall ensure that the data entered in the receiving system match the information on the customer’s shipping documents.

Welding System Assessment Goals The goal of the WSA is the development of a welding management system that provides for continual improvement, emphasizing defect prevention and the reduction of variation and waste in the supply chain.

Date of Previous Assessment: Process Controls and Confirmation. Assessment Needs Immediate Action. Reprocessing — Any process that is performed on nonconforming product so that it will meet the specified requirements.

  MANUAL DEL VIDRIO SAINT GOBAIN PDF

Records of the corrective action, including verification, shall be maintained.

Inter-locking of previous operations have occurred and quality of parts has been verified before the next operation begins. This matrix shall be readily available to management and customer at all times. In-Process and Final Tests shall be performed per frequencies in the control plan as agreed upon between the supplier and the customer.

Is there traceability of all process and tooling changes? In any case, they shall address all process steps from part receipt to part shipment and all key welding process cqi-5 as defined by the organization. Are the facilities sufficient for the welding operation? Any reprocessing activity shall require a new processing control sheet issued by qualified technical personnel denoting the necessary welding modifications. Potential suppliers More information. Date of Previous Assessment: These procedures or work instructions shall be accessible to shop floor personnel.

All special characteristics, as defined by the organization and its customers, shall be identified, defined, and addressed in the FMEA. Are the process, equipment, and safety alarm checks being tested at the required frequency or after any repair or rebuild? Reason for Change Use additional sheets if necessary: This may not be easily determined with fasteners, especially if the fastener manufacturer does systen identify the end customer auto manufacturer, tier one, etc.

Examples of operating parameters as defined by the relevant process tables. List the name stitle sphone number sand address esif available, of the principal participants from the weld organization. August 14, Document Identifier: Refer to the applicable Process Tables, Section 2. Cq-15 job audit is not the only or main focus of the WSA. CyberOptics recognizes the importance. The manual includes all CS locations More information.

Are the power supplies sufficiently sized? Weding has been established to effectively identify and address process or equipment faults With over rides or resets, logs must be maintained Weld faults audible, visible and line shut down. Examples of operating parameters as defined by the relevant process tables. If more than one assessor is required to meet the above qualifications, the lead assessor shall be the person meeting the requirements in item 1.

  ALLETHRIN SGPT PDF

The organization shall show evidence of program effectiveness. Test Frequency assessemnt Quantity: The purpose of nondestructive. Section 2 – Floor and Material Handling Responsibility It is critical that all customer requirements and lot identification be adequately transferred to internal welding documents. This process refers to receiving and shipping the parts in and out of the welding department.

CQI-15. Special Process: Welding System Assessment

If there is a separate management team or different management system, then these locations shall be considered as separate facilities. Filler Metal Specification if required: Essential Variables The Process Tables specify the tolerances of process parameters and the frequencies for checking process control parameters and assessmenr. These welding processes are designated for either gas shielded, self shielded or gasless.

The current version is. Delivery Certification By delivering products or services on the Contract, the Supplier certifies that such products or services are in weldding.

Degreed Engineer, or equivalent science degree, Certified Inspector from approved internationally recognized body, or person agreed upon between customer and supplier. It is recommended that the job audit be performed at the end of the welding system assessment.

Filler Metal Specification if required: