FLYGT 3152 PDF

2. C C Product. Submersible pump for pumping clean water, surface water and waste water containing solids or long-fibred material. Denomination. Dataplate. rpm. Max 40°C. YSER/Y//V. 26/51A. kWhp. Date: Flygt CS MT. Use our handy online form to submit details on your existing Flygt pump to get a Flygt C Submersible Pumps Range Flygt C LT Submersible.

Author: Manos Daikus
Country: Russian Federation
Language: English (Spanish)
Genre: Business
Published (Last): 15 June 2010
Pages: 258
PDF File Size: 13.68 Mb
ePub File Size: 13.31 Mb
ISBN: 426-9-52554-696-3
Downloads: 10342
Price: Free* [*Free Regsitration Required]
Uploader: Shaktigami

For the pump to perform at maximum capacity, the impeller must be adjusted regularly. Make sure that you understand the noise level requirements in the environment where the pump is installed. Limitations The warranty 1352 not cover faults caused by these situations: For more information, see Check the impeller rotation page Back off the sleeve screws a quarter turn.

Make sure that the weight of the pump does not put strain on the piping. Risk of electrical shock when pumping or mixing near a lake, jetties, beaches, ponds, fountains, or similar. Prepare for the level regulator: Grout the anchor bolts in place. Unscrew the four cap nuts and withdraw the lower wear protection from the pump housing. Lower diffuser Figure Flygt Installation, Operation, and Maintenance Manual 11 Product Description Flgt 7 6 4 3 2 5 1 12 Positio Part n Description 1 Impeller A wide range of impellers are available for dlygt applications and capacities.

See Introduction and Safety page 3. The impeller must not be allowed to make contact with the concrete floor or other hard and rough surfaces.

Product specifications | Flygt 3152 – Alaska Pump and Supply

Remove the fuses or open the circuit breaker, and check that the impeller can be rotated freely. Remove the upper wear protection. Insulation Use a megger maximum V.

  ICVERIFY 4.2 SETUP GUIDE PDF

Replace any defective equipment. Make sure that the cable cannot be sucked into the pump inlet or that it is neither sharply bent, or pinched. The phase currents vary, or they are too high. Check that the resistance between the earth ground and phase lead is more than 5 megohms. Always disconnect and lock out power before servicing to prevent unexpected startup.

Check that the cables do not have any sharp bends and are not pinched. If the impeller rotates in the wrong direction, do one of these steps: Raise the stop level. Never lift the unit by the motor cable or by the hose.

Always state the serial number of your pump when you contact Xylem, see Product Description page The data plate The data plate is a metal label located on the main body of the pump. Observe these rules when working with the product: Clean or replace if necessary. The pump will jerk in the opposite direction of the impeller rotation.

Flygt Installation, Operation, and Maintenance Manual 41 Maintenance c Place the washer on the impeller or propeller screw. This is an example of a serial number, and an explanation of its parts. When installing or maintaining explosion-proof pumps, follow these guidelines: Flygt Installation, Operation, and Maintenance Manual 49 Troubleshooting If the problem persists, refer to the Flygt Service Guide on the web or contact the local Xylem service shop.

Leakage into the electrical parts can cause damaged equipment or a blown fuse. Connect the motor cable and the starter and monitoring equipment according to the separate instructions.

  HIBBELER 12TH EDITION SOLUTIONS PDF

Flygt 3000 Series / C Submersible Pumps

Use a level or a plumb line. There must be a safety distance of at least 20 m 65 ft. Tighten the sleeve screws evenly until the flygr protection is flush against the impeller.

Recycling guidelines Always recycle according to these guidelines: The starting current in direct-on-line starting can be up to six times higher than the rated current. Flygt Installation, Operation, and Maintenance Manual 9 Transportation flyygt Storage Lifting equipment The lifting equipment must fulfill the following requirements: Check the impeller clearance.

352 FLS sensor is installed in the bottom of the stator housing. Clean all debris from the sump before starting the pump. The unit and the components can be heavy. FM approval plate Product denomination Flygt Installation, Operation, and Maintenance Manual 15 Product Description Sales denomination The sales denomination consists of the four-digit sales code and two letters that indicate the hydraulic end and type of installation.

It is recommended that they are connected to 24 V over separate fuses to protect other automatic equipment.

Flygt – Alaska Pump and Supply |

Cause Remedy The motor protection is set too low. Optional sensors Thermistor Thermistors are optional sensors for measuring the temperature. The earth ground lead must be 50 mm 2. LL Figure Dispose of all packing materials in accordance with local regulations. Install the guide bars: Flygt Installation, Operation, and Maintenance Manual 47 Flyvt Troubleshooting Introduction Follow these guidelines when troubleshooting the pump: Adjust the impeller, if necessary.