This industry-focused introduction to the CATIA V5 FEA toolset takes users from first principles through a range of real-world examples. The course starts with. This industry focused introduction to the CATIA V5 FEA toolset takes users from first principles through a range of real-world examples. The course starts with. Open the CATIA Analysis and simulation -> General Structural As soon as you enter the Generative Structural Analysis workbench, the part is.
|Published (Last):||17 June 2005|
|PDF File Size:||11.35 Mb|
|ePub File Size:||13.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
Straightforward analysis definition The analysis specifications, including loads, restraints, and material characteristics are applied directly to the design features.
CATIA V5 Generative Structural Analysis (FEA) Training
Provides rapid and accurate assessment of stress, displacement, and vibration characteristics.
The resulting deformed shape is displayed below. In FEA, restrains refer to applying displacement boundary condition which is achieved through the Restraint toolbar. The deformed shape can be plotted and the displacements scaled to ensure that they are visible.
Individual parts consisting of solid, surface and wireframe geometries can be analyzed under a variety of loading conditions. Von Mises Stress is also on Image toolbar. Interactive interpretation of results GPS provides a number of ways for a designer to understand the behavior of their design.
A cutting plane can be dynamically moved though a part, with contours shown on the cut plane, allowing the behavior of complex parts to be studied interactively. In the Compute box leave the defaults as All which means everything is tenerative.
Very nice post, thanks. Allows designers to more accurately size parts and understand the mechanical behavior of their designs. Catka boundary conditions can only be applied at the part level. The maximum stress is 4. The von Misses stress is genertive to the right. The default display is in terms analysid displacement arrows as shown on the right. Tightly integrated with knowledge-based engineering.
The course overview provides details of the topics covered in each lecture. Any of the principal stresses or the von Mises stress can be plotted.
These reports can be used to document the analyses that have been performed and to communicate the results of the analysis to other stakeholders in the organization. My Distributed force is N. The explanation of these elements is: Allows structural and modal analysis analysi be performed on parts at any stage of the design process.
When you put the force be attention when you chose the direction of it. Displacement — is available on Image toolbar. Leave a Reply Cancel reply Your email address will not be published.
It is simple now to find the limit of materials and how to make a part without resistance problems. In my case, because the front face is not in total contact with my cxtia, I made in Part Design genwrative a simple Pad, with 10 mm larger than the hole with only 0.
First steps in CATIA General Structural Analysis – beginner tutorial
This can be carried out by pointing the cursor to the top of the three, the Links Manager. The deformation image can be very deceiving strucctural one could have the impression that the wrench actually displaces to that extent. A very important thing that you must know is to find the Proprieties of a material. The size is represented with green and the sag with blue.
This course is ideal for engineers who want to analyse the structural behaviour of the parts and products they create. The non-structural mass distribution associated with the part can cafia defined using linear density, surface mass density, and point masses.
This unique capability allows collaboration and provides access to advanced PLM practices such as concurrent engineering and change management. It takes full advantage of the additional memory struuctural in 64 bit computers and will run in parallel on multi-core computers allowing the solution of very large models. Rules, checks and formulae can be used to define best practices and ensure that analyses performed are compliant with corporate standards. The analysis specifications, such as loads and restraints, are associative with the design allowing users to perform analyses quickly and easily.
Users can also switch between linear and quadratic elements and create, modify, and remove elements directly. Product Overview Product Highlights Product Key Customer Benefits Product Overview Generative Part Structural Analysis GPS allows designers to understand how their designs behave and to accurately calculate the displacements and stresses within the part under a variety of loading conditions.
We also share information about your use of our site with our social media, advertising and analytics partners. Analyses can be performed on volume parts, surface parts and wireframe geometries.
As indicated earlier, a smaller mesh could result in a more accurate solution; however, this cannot be done indiscriminately. Download the Course Overview: