HCNW 4504 PDF

HCNW Broadcom / Avago High Speed Optocouplers 1Ch 12mA mW datasheet, inventory & pricing. The HCPL and HCPL contain a GaAsP LED while the. HCPL-J and HCNW contain an AlGaAs LED. The LED is optically coupled to an. Buy Broadcom HCNW# in Avnet Americas. View Substitutes & Alternatives along with datasheets, stock, pricing and search for other Transistor .

Author: Kazizragore Nikokinos
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Photos
Published (Last): 12 November 2012
Pages: 293
PDF File Size: 7.68 Mb
ePub File Size: 17.91 Mb
ISBN: 780-8-26791-403-5
Downloads: 31973
Price: Free* [*Free Regsitration Required]
Uploader: Tygoshura

F bypass capacitor between pins 5 and 8 is recommended. The timing illustrated in Figure 17 assumes that the power transistor turns on when the optocoupler LED 450 on. When inverter power transistors switch Q1 and Q2 in Figure 17it is essential that they never conduct at the same time.

An insulating layer between a LED and an integrated photodetector provide electrical insulation between input and output. Inverters can also be designed such that the power transistor turns off when the optocoupler LED turns on; this type of design, however, requires additional fail-safe circuitry to turn off the power transistor if an over-current condition is detected.

The LED is optically coupled to an integrated high gain photo detector. These optocouplers are suitable for “safe electrical isolation” only within the safety limit data. Maintenance of the safety data shall be ensured by means of protective circuits. To ensure this, the turn-on of the optocoupler should be delayed by an amount no less than tPLHmax – tPHLminwhich also happens to be the maximum data sheet value for the propagation delay difference specification, tPLH – tPHL.

  HOSANNA MARCOS BARRIENTOS PDF

Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level.

Agilent Technologies HCNW Optocoupler Lot -5 | eBay

Propagation Delay Time vs. However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards. Contact Agilent sales representative or authorized distributor for hcjw.

The importance of these specifications is illustrated in Figure Separate connections for the photodiode bias and outputtransistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base collector capacitance.

These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements. The LED signal to turn on Q2 should be delayed enough so that an optocoupler with the very fastest turn-on propagation delay tPHLmin will never turn on before an optocoupler with the very slowest turn-off propagation delay tPLHmax turns off.

Current Transfer Ratio vs.

Agilent Technologies HCNW4504 Optocoupler Lot -5

Calculating the maximum dead time is slightly more complicated. See Option data sheet for more information. Minimizing this dead time is an important design goal for an inverter designer.

Option data sheets available.

The Input-Output Momentary Withstand Voltage is a dielectric voltage rating hcjw should not be interpreted as an input-output continuous voltage rating. Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.

For technical assistance call: Logic High Output Current vs. Device considered a two-terminal device: Under TTL load and drive conditions: Therefore, optocouplers with tight propagation delay specifications and not just shorter delays or lower pulse-width distortion can achieve short dead times in power inverters. There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances.

  ADENOSINE A1 RECEPTORS MEDIATE LOCAL ANTI-NOCICEPTIVE EFFECTS OF ACUPUNCTURE PDF

Although tPLH-tPHL max tells the designer how much delay is needed to prevent shoot-through current, it is insufficient to tell the designer how much dead time a design will have. Most inverters are designed such that the power transistor turns on when the optocoupler LED turns on; this ensures that both power transistors will be off in the event of a power loss in the control circuit.

For creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered. DC and Pulsed Transfer Characteristics.

The difference between the maximum and minimum values depends directly on the total spread in propagation delays and sets the limit on how good the worst-case dead time can be for a given design. F bypass capacitor connected between Pins 5 and 8 is recommended.

Extremely large currents will flow if there is any 45004 in their conduction during switching transitions, potentially damaging the transistors and even the surrounding circuitry. It is important to maintain accurate LED turn-on delays because delays shorter than tPLH – tPHL max may allow shootthrough currents, while longer delays will increase the worst-case dead time.

Use of nonchlorine activated fluxes is highly recommended. Use of a 0.