HORMANN UAP1 PDF

Find great deals for Hörmann Universaladapterplatine UAP 1. Shop with confidence on eBay!. For Hörmann door, Type: SupraMatic, Rotamatic / P / PL from year 09/ and LineaMatic built from 10/ – About for direction selection (up / stop / close). For inputs to Hormann: does it mean that I have to run 6 wires for this section from Loxone to Hormann? Or is it possible to reuse the wire for

Author: Zologor Goltizahn
Country: Iraq
Language: English (Spanish)
Genre: Sex
Published (Last): 7 August 2007
Pages: 52
PDF File Size: 13.40 Mb
ePub File Size: 6.78 Mb
ISBN: 794-9-91020-590-8
Downloads: 16553
Price: Free* [*Free Regsitration Required]
Uploader: Kazrazilkree

low voltage – Hormann garage door opener automation with Loxone – Home Improvement Stack Exchange

They make me able to export the analyzed data as CSV. To dig deaper into the protocoll I need more data.

Intelligent contol panels To control the door via a home automation system you have several options: Could it usp1 that you 0. Hormann garage door opener automation with Loxone Ask Question. To change the partial opening position: For that to work I needed to buy a UAP universal adapter, meant for uses like these and connect it to my Loxone miniserver.

According to the Guide you posted The UAP enables you to control the light of the supramatic open the garage door close the garage door stop the garage door check whether the door is totally closed or totally open, light status? To control the door via a home automation system you have several options:. These are the messages I was able to make sense of so far.

  GIGABYTE GA-8I945PE PDF

Reverse engeneering the Hörmann UAP1 protocoll

Unfortunately no other communication is happening when I trigger a “close door” for example. I searched the internet for information about the bus, but little hormanb nothing can be found about it.

I used the CRC calculator at http: Hardware Top side of the circuit board: Therefore I plan to hook up the bus to a network outlet I have in my garage that leads all the way down into my basement where my network rack sits.

I am an electronics amateur and can’t figure out based on the schematic below if that is correct? I hoped to find the signals there as well but it turned out that is not the case. RX Hofmann the board is powered while the logic analyzer is collecting data, we see these bytes comming in: Bus scan At startup the Master scans the bus for uqp1.

Whith that one I can tell when the UAP1 is sending and when it is receiving! Speak directly to the motor and get the signals directly onto the homeautomation system. If the selected height is too low, a 2-digit number starting with hoemann will appear with a flashing decimal point see section Connect potential free contacts directly to the motor.

Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. Dynamically assigned by the uapp1 Exactly what I want to have: The only things I get from what is stated is that if you press to open – you press the button again to stop it not a true move up move down motion.

  LIBRO CICERON LOGOPEDIA PDF

Hörmann Universaladapterplatine UAP 1

But at least I can connect to GND there. Not referenced Bit 5: Post as a guest Name. Sign up using Email and Password.

Any help would be greatly appreciated. Reverse engeneering the protocoll I expected a rather simple protocoll where no comunication happens until the UAP1 gets triggered by a switch, but I was more than wrong.

Burglar alarm As you can see the only status bit set, is from the second byte and means reversing according to the patent which makes no sense to me.

This question came from our site for electronics and electrical engineering professionals, students, and enthusiasts.

Hörmann Universaladapterplatine UAP 1 | eBay

Broadcast status From the beginning the master sends a broadcast status hormanj. Learning button assignment Bit 7: Here’s what I got using the USB converter with the door closed idling:. Home Questions Tags Users Unanswered.

Top side of the circuit board: Hi Ken, as you say in the beginning of the reply the UAP hormabn me to “open the garage door” and “close the garage door” which is what I want to achieve same as what the person who wrote the guide I linked to achievedsorry if I didn’t explain properly.

Not specified in the patent This is how far i got until now. Sign up using Facebook.