HT12D DATASHEET PDF

HT12D. 8. 4. L. Ö. RC oscillator. DIN active ²Hi². 18DIP, 20SOP. HT12F. 0 The information appearing in this Data Sheet is believed to be accurate at the. HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit.

Author: Daizilkree Doukus
Country: Papua New Guinea
Language: English (Spanish)
Genre: Software
Published (Last): 27 December 2007
Pages: 419
PDF File Size: 11.93 Mb
ePub File Size: 18.18 Mb
ISBN: 249-9-47655-305-2
Downloads: 22425
Price: Free* [*Free Regsitration Required]
Uploader: Sara

Now first of all let me acquaint you about these two integrated circuits: The serial input data is compared with the local addresses three times continuously.

This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc.

The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.

HT12D Decoder IC

Used for interfacing RF circuits generally MegaHz. Interface GPS with Arduino.

Choosing Battery for Robots. Basically found in applications of remote control systems. This oscillator can be used by connecting these two pins through a 1M Dataxheet 17 Valid Transmission VT This pin will go high when a data is received.

  IAN MCEWAN DAYDREAMER PDF

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. We should set the bits in same pattern on Encoder and Decoder IC to pair them. They are paired with 2 12 series of encoders.

HT12D/HT12F – Product Details – Holtek

It is not mandatory to use it. Interface SD Card with Arduino. Skip to main content. It is very important that your Decoder should have the same datasyeet of that of the encoder. These two ICs together form an Encoder and Decoder pair. HT12E IC has four bit parallel data inputwhich it then converts to serial data output.

HT12D Datasheet

This IC hasmany applications in short range remote controlling. Submitted by admin on 27 October This pin outputs the parallel data serially. Virgin Galactic — Commercial Space Flight. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded.

The Encoded 12 bit output data obtained from HT12E has to be given here. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Supply voltage; 5V 2. Gone dagasheet the days when we used to use wires to connect two devices to establish a communication path.

  CHINESE HEALING EXERCISES THE TRADITION OF DAOYIN PDF

I am now going to tell you about to control a certain robot wirelessly rather than using wires. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be nt12d suited for you. This pin powers the IC should use only 5V.

If any valid data is received they can be obtained from these four pins. Choosing Motor For Robots. An LED can also be connected across this terminal to indicate output. Generally a resistor of value 51 KOhms can be used. For decoding a data the IC will ht122d an oscillatorluckily this IC has one in-built.

It is mainly provided to interface RF and infrared circuits.

It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. At low signal data is transferred via antenna and received by Receiver IC which then decodes it to original parallel data. A valid transmission in indicated by a high signal at VT pin. SPI Module of Arduino.

This is an CMOS logic integrated circuit encoder.